PLCC - 4 SMD 5630 Led Street Light Spare Parts Yellow LED Chip Long Life Span

Detailed Product Description

SMT Type PLCC-4 SMD 5630 0.2W chip Yellow LED Chip Datasheet for 590-595nm wavelength

Features:

1. P-LCC-4 package.

2. White package.

3. Optical indicator.

4. Colorless clear window.

5. Ideal for backlight and light pipe application.

6. Inter reflector.

7. Wide viewing angle.

8. Suitable for automatic placement equipment.

9. Suitable for vapor-phase reflow, Infrared reflow and wave solder processes.

10. Available on tape and reel (8mm Tape).

11. The product itself will remain within RoHS compliant Version.

Descriptions:

1. The YH5630Y series is available in soft red, orange, yellow, green, blue and white. Due to the package design, the LED has wide viewing angle and optimized light coupling by inter reflector. This feature makes the SMT TOP LED ideal for light pipe application. The low current requirement makes this device ideal for portable equipment or any other application where power is at a premium.

Applications:

1. Automotive: Backlighting in dashboards and switches.

2. Telecommunication: Indicator and backlight in telephone and fax

3. Indicator and backlight for audio and video equipment.

4. Indicator and backlight in office and family equipment.

5. Flat backlight for LCD’s, switches and symbols.

6. Light pipe application.

7. General use.

Package Dimensions

Notes:

1. Luminous Intensity Measurement allowance is ± 10%.

2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.

3. It use many parameters that correspond to the CIE 1931 2°. X, Y, and Z are CIE 1931 2° values of Red, Green and Blue content of the measurement.

Please read the following notes before using the product:

1. Over-current-proof

Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).

1. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture adsorbent material (silica gel) has fabled away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: 60±5℃ for 24 hours.

1. Soldering Condition

3.1 Pb-free solder temperature profile.

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

1. Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.

1. Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

1. Caution in ESD

Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded.